Peugeot 208 Key Replacement
It is best to delegate the replacement of Peugeot keys 208 to auto locksmiths equipped with the equipment and skills. They can create and program keys faster and less expensive than a dealership.
If your key fob has stopped locking or unlocking your doors it is likely due to a dead coin battery. There are also other reasons for the key to be malfunctioning.
Dead Coin Battery
A dead coin battery can stop your Peugeot 208 from locking or unlocking and will not allow you to start the engine. If this is the case, you'll need to make use of the backup starting procedure that is described in your vehicle's owner manual.
Another reason the 208 won't start is that the spark plugs have been damaged. The spark plugs are responsible to ignite the fuel that ignites the engine. They only last for a certain amount of time. They will eventually break down if they're not used enough.
Fortunately, there's an easy solution to this issue. The best way to solve this issue is to measure the voltage of your car battery with a multimeter. If it is below 11.5 Volts and you are not satisfied, then it is time to replace it. If the battery is damaged it is necessary to clean its contacts. This can be done by removing the rubber cover from the two terminals of the battery, and then using a wirebrush, you can remove any corroded battery parts. Then, you should connect the cables to the positive and negative poles.
Water Damage
If your 208 does not start and the battery hasn't been replaced, you must check the spark plugs. It is possible that they're dirty, causing them to not to spark. This can be easily corrected by cleaning the spark plugs in an workshop.
Peugeot cars are equipped with transponder keys that works with the car's immobiliser system. This guarantees that only the right key can turn the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the correct signal to the vehicle.
This is a very common issue that can occur due to water damage. This is a typical issue in areas with colder temperatures where the vehicle is exposed to rain or snow. If this is the case, seek out a reputable auto locksmith who has all of the tools and equipment required to modify the new key. They will also have the most up-to-date technology and equipment needed to create the Peugeot 208 smart key. The process should take no more than 15 minutes.
Contacts of the battery may be damaged.
Peugeot changed from the old carbon-encased transponder chips to a brand new type of chip that uses electronic components within circuit boards. The new system is excellent when it's new, however the circuit boards degrade over time and stop working properly.
This could stop the immobiliser from working, so your vehicle won't start. Contact an Peugeot specialist, or a locksmith if this is the case.
A common problem is when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A car locksmith will replace the battery, and cut a new blade for you. This is a quick solution.
Faulty Receiver Module
It could be that the receiver module is faulty when your Peugeot key fob fails to function after being dropped on the floor, exposed to a sudden rainstorm or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer which manages the central locking system of your Peugeot vehicle.
The rubber seals on the key fob stop water from reaching the electronic chip. However prolonged exposure to water can break through these seals, causing damage to the chip. The high salt content of the ocean water or pool could cause damage to the key fob if it is submerged.
The module must be replaced if the Peugeot spare key does not work anymore. This should be done by a Peugeot specialist or expert auto locksmith. Unlike other cars, Peugeot keys are protected by an exclusive immobilizer system that requires the right coding to begin the engine. It is for this reason that you should only trust the Peugeot locksmith to design and program an alternative.
Computer on board is not working properly
The computer on board of your Peugeot is responsible many features in your car, including airbags and power windows. The computer on board will display the code when something goes wrong. This code is stored in the system and will stay there until the issue is solved. This may require the on-board computers to be replaced.
The most common cause of the warning light of the airbag to turn on is corrosion or loose connections within the sensor. It can be due to wear and tear, ageing, or exposure to moisture and salt. It is crucial to get this issue resolved as soon as you can, since an airbag that is not functioning properly could be dangerous in the event of an accident.
If your Peugeot is showing a card not detected error, then the key battery inside the key fob could be dead or weak. This can prevent the key fob from sending a signal that disables your vehicle's immobilizer. Try this by pressing the unlock button on the fob's key and then trying to start your vehicle. If peugeot 206 key does not work the battery on the key needs to be replaced.